testActions:
  prereq_147: &prereq_147
    id: prereq_147
    document: '<p>在热停堆工况(热功率稳定)，平均温度最大允许变化&lt;0.2℃；若KIC中显示的三个环路平均温度变化AT&gt;0.2℃，则采取数据滑动平均方式，期间确保三个环路平均温度的滑动平均值最大最小值之差&lt;0.2℃、测量时间大于滑动周期。</p>'
    mode: manual
    dataFields:
      - tableRef: '#/tables/manualConfirm'
        fields: [confirm_147]
  prereq_150: &prereq_150
    id: prereq_150
    document: '<p>三个蒸发器处于稳定状态，压力一致。</p>'
    mode: manual
    dataFields:
      - tableRef: '#/tables/manualConfirm'
        fields: [confirm_150]
  prereq_43: &prereq_43
    id: prereq_43
    document: '<p>蒸汽发生器水位稳定。</p>'
    mode: manual
    dataFields:
      - tableRef: '#/tables/manualConfirm'
        fields: [confirm_43]
  prereq_75: &prereq_75
    id: prereq_75
    document: '<p>RCV的一个下泄孔板投入运行；确保测量期间无下泄孔板相关操作，一回路温度保持稳定，测量结果若超差需要分析下泄流量影响。</p>'
    mode: manual
    dataFields:
      - tableRef: '#/tables/manualConfirm'
        fields: [confirm_75]
  prereq_92: &prereq_92
    id: prereq_92
    document: '<p>其它模式/工况下需进行相应的独立风险分析。</p>'
    mode: manual
    dataFields:
      - tableRef: '#/tables/manualConfirm'
        fields: [confirm_92]
  pre_153: &pre_153
    id: pre_153
    document: '<p>本程序适用于热停堆(热功率稳定)工况下执行RCP63程序，统一进行Sensor Check部分使用。</p>'
    mode: manual
    dataFields:
      - tableRef: '#/tables/manualConfirm'
        fields: [confirm_153]
  pre_136: &pre_136
    id: pre_136
    document: '<p>执行前确认KIC中一回路三个环路平均温度变化量不超过0.2℃。</p>'
    mode: auto
    functionType: DATA_ACQUISITION_WITH_VALIDATION
    functionParameters:
      - RCP614KM
      - RCP618KM
      - RCP622KM
    dataFields:
      - tableRef: '#/tables/temperatureCheckTable'
        fields: [loop1TempVariation, loop2TempVariation, loop3TempVariation]
  pre_137: &pre_137
    id: pre_137
    document: '<p>若三环路平均温度变化超过0.2℃，记录滑动周期、各环路滑动平均最大最小值之差及最短数据测量时间，确认均满足≤0.2℃且测量时间&gt;滑动周期。</p>'
    mode: auto
    functionType: DATA_ACQUISITION_WITH_VALIDATION
    functionParameters:
      - RCP614KM
      - RCP618KM
      - RCP622KM
      - RCP612KM
      - RCP616KM
      - RCP620KM
      - RCP613KM
      - RCP617KM
      - RCP621KM
      - RCP611KM
      - RCP615KM
      - RCP619KM
    dataFields:
      - tableRef: '#/tables/temperatureCheckTable'
        fields: [loop1TempVariation, loop2TempVariation, loop3TempVariation]
  pre_138: &pre_138
    id: pre_138
    document: '<p>确认 RPR、RPN上无相关的试验检修工作。</p>'
    mode: manual
    dataFields:
      - tableRef: '#/tables/manualConfirm'
        fields: [confirm_138]
  pre_139: &pre_139
    id: pre_139
    document: '<p>按附表1检查相关模拟量指示并记录，确认结果满意。</p>'
    mode: auto
    functionType: DATA_ACQUISITION
    functionParameters:
      - RCP614KM
      - RCP618KM
      - RCP622KM
    dataFields:
      - tableRef: '#/tables/alarmCheckTable'
        cells:
          - row: RCP614KM
            column: preInspectionStatus
          - row: RCP618KM
            column: preInspectionStatus
          - row: RCP622KM
            column: preInspectionStatus
  pre_140: &pre_140
    id: pre_140
    document: '<p>试验前根据附表1报警清单检查报警，确认无异常报警，方可进行后续检查工作。</p>'
    mode: auto
    functionType: DATA_ACQUISITION
    functionParameters:
      - RCP455AA
      - RPAB138AA
      - RPAB167AA
      - RPAB171AA
    dataFields:
      - tableRef: '#/tables/alarmCheckTable'
        cells:
          - row: RCP455AA
            column: preInspectionStatus
          - row: RPAB138AA
            column: preInspectionStatus
          - row: RPAB167AA
            column: preInspectionStatus
          - row: RPAB171AA
            column: preInspectionStatus
  x5KicReadingsPreCheck: &x5KicReadingsPreCheck
    id: x5KicReadingsPreCheck
    document: '<p>采集X5端子排拆前KIC指示值。</p>'
    mode: auto
    functionType: DATA_ACQUISITION
    functionParameters:
      - RCP030MT
      - RCP033MT
    dataFields:
      - tableRef: '#/tables/kicReadingsTable'
        cells:
          - row: RCP030MT
            column: preInspectionValue
          - row: RCP033MT
            column: preInspectionValue
  x5KicReadingsPostCheck: &x5KicReadingsPostCheck
    id: x5KicReadingsPostCheck
    document: '<p>采集X5端子排恢复后KIC指示值。</p>'
    mode: auto
    functionType: DATA_ACQUISITION
    functionParameters:
      - RCP030MT
      - RCP033MT
    dataFields:
      - tableRef: '#/tables/kicReadingsTable'
        cells:
          - row: RCP030MT
            column: postInspectionValue
          - row: RCP033MT
            column: postInspectionValue
  rcp030mtResistance: &rcp030mtResistance
    id: rcp030mtResistance
    mode: auto
    functionType: RESISTANCE_4WIRE
    channel: input1
    functionParameters:
    document: '<p><strong>测量位置：</strong>KCSO13AR/EB911/X5</p><p><strong>测量项目：</strong>R1/2, R1/3, R1/4, R2/3, R2/4, R3/4, R/4wires</p>'
    dataFields:
      - tableRef: '#/tables/resistanceMeasurementTable'
        cells:
          - row: RCP030MT
            column: r12
          - row: RCP030MT
            column: r13
          - row: RCP030MT
            column: r14
          - row: RCP030MT
            column: r23
          - row: RCP030MT
            column: r24
          - row: RCP030MT
            column: r34
          - row: RCP030MT
            column: r4wires
    uploadStrategy: inherit
  rcp030mtInsulation: &rcp030mtInsulation
    id: rcp030mtInsulation
    mode: auto
    functionType: INSULATION
    channel: input1
    functionParameters:
      testVoltage: 50
      testTime: 20
      dischargeTime: 5
    document: '<p><strong>测量位置：</strong>KCSO13AR/EB911/X5</p><p><strong>注意事项：</strong></p><ul><li>测试电压50V</li><li>测试时间不小于20秒</li><li>测量后探头对地放电</li></ul>'
    dataFields:
      - tableRef: '#/tables/resistanceMeasurementTable'
        cells:
          - row: RCP030MT
            column: insulation
    uploadStrategy: inherit
  rcp033mtResistance: &rcp033mtResistance
    id: rcp033mtResistance
    mode: auto
    functionType: RESISTANCE_4WIRE
    channel: input1
    functionParameters:
    document: '<p><strong>测量位置：</strong>KCSO13AR/EB911/X5</p><p><strong>测量项目：</strong>R1/2, R1/3, R1/4, R2/3, R2/4, R3/4, R/4wires</p>'
    dataFields:
      - tableRef: '#/tables/resistanceMeasurementTable'
        cells:
          - row: RCP033MT
            column: r12
          - row: RCP033MT
            column: r13
          - row: RCP033MT
            column: r14
          - row: RCP033MT
            column: r23
          - row: RCP033MT
            column: r24
          - row: RCP033MT
            column: r34
          - row: RCP033MT
            column: r4wires
    uploadStrategy: inherit
  rcp033mtInsulation: &rcp033mtInsulation
    id: rcp033mtInsulation
    mode: auto
    functionType: INSULATION
    channel: input1
    functionParameters:
      testVoltage: 50
      testTime: 20
      dischargeTime: 5
    document: '<p><strong>测量位置：</strong>KCSO13AR/EB911/X5</p><p><strong>注意事项：</strong></p><ul><li>测试电压50V</li><li>测试时间不小于20秒</li><li>测量后探头对地放电</li><li>复归保险FB059 F11和F12</li></ul>'
    dataFields:
      - tableRef: '#/tables/resistanceMeasurementTable'
        cells:
          - row: RCP033MT
            column: insulation
    uploadStrategy: inherit
  rcp031mtResistance: &rcp031mtResistance
    id: rcp031mtResistance
    mode: auto
    functionType: RESISTANCE_4WIRE
    channel: input1
    functionParameters:
    document: '<p><strong>测量位置：</strong>KCS013AR/EB911/X6</p><p><strong>测量项目：</strong>R1/2, R1/3, R1/4, R2/3, R2/4, R3/4, R/4wires</p>'
    dataFields:
      - tableRef: '#/tables/resistanceMeasurementTable'
        cells:
          - row: RCP031MT
            column: r12
          - row: RCP031MT
            column: r13
          - row: RCP031MT
            column: r14
          - row: RCP031MT
            column: r23
          - row: RCP031MT
            column: r24
          - row: RCP031MT
            column: r34
          - row: RCP031MT
            column: r4wires
    uploadStrategy: inherit
  rcp031mtInsulation: &rcp031mtInsulation
    id: rcp031mtInsulation
    mode: auto
    functionType: INSULATION
    channel: input1
    functionParameters:
      testVoltage: 50
      testTime: 20
      dischargeTime: 5
    document: '<p><strong>测量位置：</strong>KCS013AR/EB911/X6</p><p><strong>注意事项：</strong></p><ul><li>测试电压50V</li><li>测试时间不小于20秒</li><li>测量后探头对地放电</li></ul>'
    dataFields:
      - tableRef: '#/tables/resistanceMeasurementTable'
        cells:
          - row: RCP031MT
            column: insulation
    uploadStrategy: inherit
  rcp034mtResistance: &rcp034mtResistance
    id: rcp034mtResistance
    mode: auto
    functionType: RESISTANCE_4WIRE
    channel: input1
    functionParameters:
    document: '<p><strong>测量位置：</strong>KCS013AR/EB911/X6</p><p><strong>测量项目：</strong>R1/2, R1/3, R1/4, R2/3, R2/4, R3/4, R/4wires</p>'
    dataFields:
      - tableRef: '#/tables/resistanceMeasurementTable'
        cells:
          - row: RCP034MT
            column: r12
          - row: RCP034MT
            column: r13
          - row: RCP034MT
            column: r14
          - row: RCP034MT
            column: r23
          - row: RCP034MT
            column: r24
          - row: RCP034MT
            column: r34
          - row: RCP034MT
            column: r4wires
    uploadStrategy: inherit
  rcp034mtInsulation: &rcp034mtInsulation
    id: rcp034mtInsulation
    mode: auto
    functionType: INSULATION
    channel: input1
    functionParameters:
      testVoltage: 50
      testTime: 20
      dischargeTime: 5
    document: '<p><strong>测量位置：</strong>KCS013AR/EB911/X6</p><p><strong>注意事项：</strong></p><ul><li>测试电压50V</li><li>测试时间不小于20秒</li><li>测量后探头对地放电</li></ul>'
    dataFields:
      - tableRef: '#/tables/resistanceMeasurementTable'
        cells:
          - row: RCP034MT
            column: insulation
    uploadStrategy: inherit
  rcp043mtResistance: &rcp043mtResistance
    id: rcp043mtResistance
    mode: auto
    functionType: RESISTANCE_3WIRE
    channel: input1
    functionParameters:
    document: '<p><strong>测量位置：</strong>KCSO13AR/EB902/X1</p><p><strong>测量项目：</strong>R2/3, R2/4, R3/4</p><p><strong>注意：</strong>3线制传感器</p>'
    dataFields:
      - tableRef: '#/tables/resistanceMeasurementTable'
        cells:
          - row: RCP043MT
            column: r23
          - row: RCP043MT
            column: r24
          - row: RCP043MT
            column: r34
    uploadStrategy: inherit
  rcp043mtInsulation: &rcp043mtInsulation
    id: rcp043mtInsulation
    mode: auto
    functionType: INSULATION
    channel: input1
    functionParameters:
      testVoltage: 50
      testTime: 20
      dischargeTime: 5
    document: '<p><strong>测量位置：</strong>KCSO13AR/EB902/X1</p><p><strong>注意事项：</strong></p><ul><li>测试电压50V</li><li>测试时间不小于20秒</li><li>测量后探头对地放电</li></ul>'
    dataFields:
      - tableRef: '#/tables/resistanceMeasurementTable'
        cells:
          - row: RCP043MT
            column: insulation
    uploadStrategy: inherit
  rcp044mtResistance: &rcp044mtResistance
    id: rcp044mtResistance
    mode: auto
    functionType: RESISTANCE_3WIRE
    channel: input1
    functionParameters:
    document: '<p><strong>测量位置：</strong>KCSO13AR/EB902/X1</p><p><strong>测量项目：</strong>R2/3, R2/4, R3/4</p><p><strong>注意：</strong>3线制传感器</p>'
    dataFields:
      - tableRef: '#/tables/resistanceMeasurementTable'
        cells:
          - row: RCP044MT
            column: r23
          - row: RCP044MT
            column: r24
          - row: RCP044MT
            column: r34
    uploadStrategy: inherit
  rcp044mtInsulation: &rcp044mtInsulation
    id: rcp044mtInsulation
    mode: auto
    functionType: INSULATION
    channel: input1
    functionParameters:
      testVoltage: 50
      testTime: 20
      dischargeTime: 5
    document: '<p><strong>测量位置：</strong>KCSO13AR/EB902/X1</p><p><strong>注意事项：</strong></p><ul><li>测试电压50V</li><li>测试时间不小于20秒</li><li>测量后探头对地放电</li><li>复归保险FB005 F11和F12</li><li>请主控确认报警消除</li></ul>'
    dataFields:
      - tableRef: '#/tables/resistanceMeasurementTable'
        cells:
          - row: RCP044MT
            column: insulation
    uploadStrategy: inherit
testActivityGroups:
  prerequisites: &prerequisites
    id: prerequisites
    name: 3.0先决条件
    actions:
      - *prereq_147
      - *prereq_150
      - *prereq_43
      - *prereq_75
      - *prereq_92
  preInspectionChecks: &preInspectionChecks
    id: preInspectionChecks
    name: 5.1试验前状态说明和检查
    tableRefs:
      - '#/tables/temperatureCheckTable'
      - '#/tables/alarmCheckTable'
    actions:
      - *pre_153
      - *pre_136
      - *pre_137
      - *pre_138
      - *pre_139
      - *pre_140
  protectionIGroup: &protectionIGroup
    id: protectionIGroup
    name: 5.2保护Ⅰ组传感器及线缆绝缘及电阻检查
    tableRefs:
      - '#/tables/kicReadingsTable'
      - '#/tables/resistanceMeasurementTable'
    actions:
      - *x5KicReadingsPreCheck
      - *rcp030mtResistance
      - *rcp030mtInsulation
      - *rcp033mtResistance
      - *rcp033mtInsulation
      - *x5KicReadingsPostCheck
testTaskGroups:
  prerequisitesTask: &prerequisitesTask
    id: prerequisitesTask
    name: 3.0先决条件
    stages:
      - *prerequisites
  preInspectionTask: &preInspectionTask
    id: preInspectionTask
    name: 5.1试验前状态说明和检查
    stages:
      - *preInspectionChecks
  protectionITask: &protectionITask
    id: protectionITask
    name: 5.2保护Ⅰ组传感器及线缆绝缘及电阻检查
    stages:
      - *protectionIGroup
resultDisplays:
  finalResultDisplay: &finalResultDisplay
    id: finalResultDisplay
    name: 实验结果汇总
    document: '<p>显示本次实验的所有测量数据和检查结果</p>'
    tableRefs:
      - '#/tables/resistanceMeasurementTable'
      - '#/tables/temperatureCheckTable'
      - '#/tables/alarmCheckTable'
      - '#/tables/kicReadingsTable'
procedure:
  id: SIMPLE63
  name: 范例 一回路温度传感器绝缘和连续性检查 TP RCP63
  version: SIMPLE
  activitySequence:
    - *prerequisitesTask
    - *preInspectionTask
    - *protectionITask
    - *finalResultDisplay
tables:
  kicReadingsTable:
    id: kicReadingsTable
    name: KIC指示读数表
    description: 检验前后的KIC指示读数
    tableType: grid
    isShared: true
    uploadStrategy: onComplete
    columnHeaders:
      - id: preInspectionValue
        name: 拆前数据
        type: numeric
        isRequired: true
        unit: '℃'
      - id: postInspectionValue
        name: 拆后数据
        type: numeric
        isRequired: true
        unit: '℃'
    rowHeaders:
      - id: RCP030MT
        name: RCP030MT
      - id: RCP033MT
        name: RCP033MT
      - id: RCP031MT
        name: RCP031MT
      - id: RCP034MT
        name: RCP034MT
      - id: RCP043MT
        name: RCP043MT
      - id: RCP044MT
        name: RCP044MT
  alarmCheckTable:
    id: alarmCheckTable
    name: 试验前后报警检查记录表
    description: 依据TP RCP63的报警检查记录结构
    tableType: grid
    isShared: true
    uploadStrategy: onComplete
    columnHeaders:
      - id: signal
        name: 信号
        type: text
        isRequired: false
      - id: description
        name: 描述
        type: text
        isRequired: false
      - id: location
        name: 位置
        type: text
        isRequired: false
      - id: normalState
        name: 正常状态
        type: text
        isRequired: false
      - id: eventTime
        name: 出现时间
        type: text
        isRequired: false
      - id: preInspectionStatus
        name: 拆前状态
        type: text
        isRequired: true
      - id: preInspectionStatusB
        name: 拆前B列
        type: text
        isRequired: false
      - id: postInspectionStatus
        name: 拆后状态
        type: text
        isRequired: true
      - id: postInspectionStatusB
        name: 拆后B列
        type: text
        isRequired: false
    rowHeaders:
      - id: RCP455AA
        name: RCP455AA
      - id: RPAB138AA
        name: RPA/B138AA
      - id: RPAB167AA
        name: RPA/B167AA
      - id: RPAB171AA
        name: RPA/B171AA
      - id: RPA_B079AA
        name: RPA/B079AA
      - id: RPA_B039LA
        name: RPA/B039LA
      - id: RCP614KM
        name: RCP614KM
      - id: RCP618KM
        name: RCP618KM
      - id: RCP622KM
        name: RCP622KM
  manualConfirm:
    id: manualConfirm
    name: 人工确认
    tableType: form
    uploadStrategy: immediate
    layoutConfig:
      totalColumns: 12
    fields:
      - id: confirm_147
        name: 确认 147
        type: boolean
        layoutConfig:
          labelSpan: 4
          valueSpan: 8
      - id: confirm_150
        name: 确认 150
        type: boolean
        layoutConfig:
          labelSpan: 4
          valueSpan: 8
      - id: confirm_43
        name: 确认 43
        type: boolean
        layoutConfig:
          labelSpan: 4
          valueSpan: 8
      - id: confirm_75
        name: 确认 75
        type: boolean
        layoutConfig:
          labelSpan: 4
          valueSpan: 8
      - id: confirm_92
        name: 确认 92
        type: boolean
        layoutConfig:
          labelSpan: 4
          valueSpan: 8
      - id: confirm_153
        name: 确认 153
        type: boolean
        layoutConfig:
          labelSpan: 4
          valueSpan: 8
      - id: confirm_138
        name: 确认 138
        type: boolean
        layoutConfig:
          labelSpan: 4
          valueSpan: 8
      - id: confirm_142
        name: 确认 142
        type: boolean
        layoutConfig:
          labelSpan: 4
          valueSpan: 8
  resistanceMeasurementTable:
    id: resistanceMeasurementTable
    name: 电阻测量表
    description: 传感器的电阻和绝缘测量数据
    tableType: grid
    uploadStrategy: onComplete
    columnHeaders:
      - id: r12
        name: R1/2
        type: numeric
        isRequired: false
        unit: Ω
      - id: r13
        name: R1/3
        type: numeric
        isRequired: false
        unit: Ω
      - id: r14
        name: R1/4
        type: numeric
        isRequired: false
        unit: Ω
      - id: r23
        name: R2/3
        type: numeric
        isRequired: true
        unit: Ω
      - id: r24
        name: R2/4
        type: numeric
        isRequired: true
        unit: Ω
      - id: r34
        name: R3/4
        type: numeric
        isRequired: true
        unit: Ω
      - id: r4wires
        name: R/4wires
        type: numeric
        isRequired: false
        unit: Ω
      - id: insulation
        name: Insulation
        type: numeric
        isRequired: true
        unit: MΩ
    rowHeaders:
      - id: RCP030MT
        name: RCP030MT
      - id: RCP033MT
        name: RCP033MT
      - id: RCP031MT
        name: RCP031MT
      - id: RCP034MT
        name: RCP034MT
      - id: RCP043MT
        name: RCP043MT
      - id: RCP044MT
        name: RCP044MT
  temperatureCheckTable:
    id: temperatureCheckTable
    name: 环路温度检查表
    description: 环路平均温度变化量检查
    tableType: form
    uploadStrategy: onComplete
    layoutConfig:
      totalColumns: 12
    fields:
      - id: loop1TempVariation
        name: 一环路平均温度变化量
        type: numeric
        isRequired: true
        unit: '℃'
        layoutConfig:
          labelSpan: 4
          valueSpan: 8
          order: 1
      - id: loop2TempVariation
        name: 二环路平均温度变化量
        type: numeric
        isRequired: true
        unit: '℃'
        layoutConfig:
          labelSpan: 4
          valueSpan: 8
          order: 2
      - id: loop3TempVariation
        name: 三环路平均温度变化量
        type: numeric
        isRequired: true
        unit: '℃'
        layoutConfig:
          labelSpan: 4
          valueSpan: 8
          order: 3